fire alarm system has different components working together to detect and warn people through smoke, fire, carbon monoxide or other emergencies are present. These alarms may be activated automatically or manually. If smoke detectors, fire detectors, and heat detectors are installed then they sense the fire smoke and heat and gives a signal to hooter and it automatically creates a sound or may also be activated via manual fire alarm activation devices such as manual pull stations.

It is very important for the safety of home. In case of fire, the fire alarm system supports and keeps you aware before the fire spread all over the place.

Fire Alaram &Detection Systems

Fire Alarm Control Panels

Fire Alarm Devices

Smoke Detectors

Thermal Detectors

Flame Detector

Fire & Gas Detector

Fire Alaram & Detection Systems in karachi pakistan

Fire Alarm Control Panels


Traditional fire alarm panels installed prior to 1998 were conventional zone panels. In a zoned system, fire alarm devices in a common area or floor of a facility are connected to the same alarm initiating circuit. Each zone requires its own circuit conductor. This arrangement allows alarm annunciation to be reported by areas of the building to identify which device is in alarm. Conventional panels are often used in small facilities where a few zones can provide sufficient alarm annunciation.


With the advent of microprocessors and digital electronics, addressable fire alarm control panels, and devices have become more common than conventional systems for medium and large-sized facilities. They have become more cost-effective in some small applications as well.

Addressable fire alarm systems use digital encoding and multiplex technology to more accurately identify alarm locations and device conditions. Each fire alarm device in a system is programmed with a unique address.

The fire alarm control panel is capable of communicating with a single address or a group of addresses depending on the functions required. The communication is often multiplexed over a common cable, sometimes referred to as the signaling line circuit (SLC).

This arrangement significantly reduces the amount of cabling necessary to install the system. The communication channel allows two-way communication, thus enabling the fire alarm control panel to control as well as monitor fire alarm devices.

A significant component of an addressable fire alarm system is the software programming necessary to make the system function correctly. The programming allows for flexible applications where you want to have specific control over the inputs and outputs.

The communication technologies employed in addressable systems allow for advanced features to accommodate sensitivity changes due to age and accumulation of dust prior to maintenance. These features are not available with the standard conventional system.

control panels

Fire Alarm Control Panels in karachi pakistan

Fire Alarm Devices

Automatic Detection

Components of fire consist of:

Smoke (particulate and aerosol)


Light Radiation

Fire detection devices are built to detect one or a combination of these components. While all components are necessary for a fire to exist, all components may not exist at a detectable threshold.

Detectors will be selected that will detect the elements that may exist in a fire for the ambient conditions that are present.

It also should be realized the similar non-fire components might exist in the same ambient conditions, which could cause unfavorable false alarm conditions.

Devices used for fire detection include smoke detectors, thermal detectors, flame detectors, fire-gas detectors, and other devices.

Smoke detectors sense visible or invisible particles of combustion generated by burning, smoldering or the incipient stage of combustion.

These devices fall into two categories — photoelectric and ionization.

Thermal detectors sense the high temperature or the temperature rise caused by a fire.

Flame detectors sense the radiation produced by a fire.

Fire-gas detectors sense the gases produced by a fire.

Other detectors sense some phenomenon other than smoke, thermal, flame, or fire-gas to detect a fire.

Fire Alarm Devices

Fire Alarm Devices Automatic Detection in Karachi Pakistan

Smoke Detectors

There are three types of smoke detectors: Ionization, photoelectric, and combination.


The ionization smoke detector is widely used. Its capability to detect smoke originating from fire is best utilized for clean-burning fires that produce small particles during combustion.

The ionization smoke detector consists of an alpha particle producing a radioactive source, a smoke chamber, and charged detector plates.

The alpha source causes the air within the smoke chamber to become ionized and conductive

As smoke particles enter the smoke chamber, the smoke particles attach themselves to the ionized air molecules and the air in the chamber becomes less conductive

When the air conductivity within the chamber drops below a predetermined level, the alarm is triggered

Advantages of Ionization Smoke Detectors:

Detects invisible products of combustion — It can detect fires that are in the incipient stage or detect other aerosol-type smoke products

Quick-acting — Provides for earlier detection than other types of smoke detectors or thermal detectors

Disadvantages of Ionization Smoke Detectors: .